为了测试路由的 failover,我们把连接网段 10.0.0.0/24 的路由器 A 上的网络连接断开 。经过总计约两分钟的过期时间以后,Zebra 得到了另一个可达 10.0.0.0/24 的路由,这个新的路由是通过路由器 B 得到的 。注重在下面的清单中,Zebra 通过 192.168.1.2 到达 10.0.0.0/24,而不是先前的路径 。
清单 13. Zebra 反映的 RIP 路由
Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF,
B - BGP, > - selected route, * - FIB route
R>* 10.0.0.0/24 [120/3] via 192.168.1.2, eth0, 00:00:26
R>* 10.0.1.0/24 [120/2] via 192.168.1.2, eth1, 00:06:02
C>* 10.0.2.0/24 is directly connected, dummy0
K * 127.0.0.0/8 is directly connected, lo
C>* 127.0.0.0/8 is directly connected, lo
R>* 192.168.0.0/30 [120/2] via 192.168.1.2, eth1, 00:00:26
C>* 192.168.1.0/30 is directly connected, eth1
C>* 192.168.2.0/30 is directly connected, eth0
为什么总的过期时间大于两分钟?RIP 默认的过期时间是 30 秒,但是 RIP 协议指定了在确认一个路由已经失效之前要进行 3 次重试(共 90 秒),并且还要有一段时间来清空无效的路由(还需要 240 秒) 。众所周知,RIP 协议对连接失败反应迟钝,这一点在这里得到了明确的论证 。
这里是在 failover 发生之前路由器 A 的路由表的输出 。
清单 14. Failover 之前路由器 A 的路由表
RouterA#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/24 is subnetted, 3 subnets
R10.0.2.0 [120/1] via 192.168.2.1, 00:00:11, FastEthernet0/0
C10.0.0.0 is directly connected, Loopback0
R10.0.1.0 [120/1] via 192.168.0.2, 00:00:18, Serial0/0
192.168.0.0/30 is subnetted, 1 subnets
C192.168.0.0 is directly connected, Serial0/0
192.168.1.0/30 is subnetted, 1 subnets
R192.168.1.0 [120/1] via 192.168.0.2, 00:00:18, Serial0/0
[120/1] via 192.168.2.1, 00:00:11, FastEthernet0/0
192.168.2.0/30 is subnetted, 1 subnets
C192.168.2.0 is directly connected, FastEthernet0/0
failover 之后:
清单 15. Failover 之后路由器 A 的路由表
RouterA#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/24 is subnetted, 3 subnets
R10.0.2.0 [120/2] via 192.168.0.2, 00:00:09, Serial0/0
C10.0.0.0 is directly connected, Loopback0
R10.0.1.0 [120/1] via 192.168.0.2, 00:00:09, Serial0/0
192.168.0.0/30 is subnetted, 1 subnets
C192.168.0.0 is directly connected, Serial0/0
192.168.1.0/30 is subnetted, 1 subnets
R192.168.1.0 [120/1] via 192.168.0.2, 00:00:09, Serial0/0
192.168.2.0/30 is subnetted, 1 subnets
推荐阅读
- 如何删除IOS--CISCOIFS简介
- Cisco2610A的配置实例
- CISCO学习问题之Cisco路由器中ACL的参数establish的作用
- 五种经典方式来巧妙设置路由器
- Cisco路由器上手工方式VPN的实现
- 介绍两种恢复CISCOIOS的方法
- 掌握CiscoIOS测试命令的多种用法
- Cisco路由器使用问题集锦
- 教您五种经典方式来巧妙设置路由器
- Cisco路由器封锁BT新法介绍
