多层交换学习资料 _云知道

In the example above, PC-A wants to communicate with PC-B. They are in different VLANs so the traffic will be routed via the RSM (default gateway for the PCs). The first packet will be sent by PC-A and routed by the RSM towards PC-B; a shortcut, PC-A --> PC-B, will be created and all subsequent packets will be Layer 3 switched by the MLS-SE (Supervisor=NFFC).
PC-A#ping 12.12.12.12
!-- pinging PC-B
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 12.12.12.12, timeout is 2 seconds:
!!!!!
SUCcess rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms
On the switch:
switch-MLS-SE (enable) show mls entry
Destination IP Source IP Prot DstPrt SrcPrt Destination Mac Vlan Port
--------------- --------------- ---- ------ ------ ----------------- ---- -----
MLS-RP 11.11.11.1:
11.11.11.11 12.12.12.12 ICMP - - 00-d0-58-43-9f-60 11 6/11
!-- As in the note above we have two shortcuts A->B and B->A
12.12.12.12 11.11.11.11 ICMP - - 00-00-0c-07-ac-01 12 6/12
switch-MLS-SE (enable)
switch-MLS-SE (enable) show mls
Multilayer switching enabled
!-- By default, MLS is enabled on the switch
Multilayer switching aging time = 256 seconds
Multilayer switching fast aging time = 0 seconds, packet threshold = 0
Current flow mask is Destination flow
Configured flow mask is Destination flow
Total packets switched = 8
!-- Five echos and five replies were sent; the first echo and reply went
!-- through the RSM and subsequent were Layer 3 switched, which gives us a total of
!-- eight Layer 3 switched packets and two shortcuts.
Active shortcuts = 2
Netflow Data EXPort disabled
Total packets exported = 0
MLS-RP IP MLS-RP ID XTAG MLS-RP MAC-Vlans
---------------- ------------ ---- ---------------------------------
11.11.11.1 00100b108800 2 00-10-0b-10-88-00 11-12
switch-MLS-SE (enable)
switch-MLS-SE (enable) show mls statistics rp
Total packets switched = 8
Active shortcuts = 2
Total packets exported= 0
Total switched
MLS-RP IP MLS-RP ID packets bytes
--------------- ------------ ---------- ------------
11.11.11.1 00100b108800 8 944
switch-MLS-SE (enable)
RSM-MLS-RP#sho mls rp
multilayer switching is globally enabled
mls id is 0010.0b10.8800
mls ip address 11.11.11.1
!-- IP address of MLS-RP
mls flow mask is destination-ip
number of domains configured for mls 1
vlan domain name: sales
current flow mask: destination-ip
current sequence number: 3150688457
current/maximum retry count: 0/10
current domain state: no-change
current/next global purge: false/false
current/next purge count: 0/0
domain uptime: 1d00h
keepalive timer expires in 8 seconds
retry timer not running
change timer not running
1 management interface(s) currently defined:
vlan 11 on Vlan11
2 mac-vlan(s) configured for multi-layer switching:
mac 0010.0b10.8800
vlan id(s)
11 12
!-- VLANs, interfaces participating in MLS
router currently aware of following 1 switch(es):
switch id 0050.d133.2bff
!-- MAC address of the MLS-SE
On the switch, MLS is enabled by default. There is no need to specify the MLS-RP IP address if it is the RSM. However, for an external router acting as the MLS-RP, we need to configure the switch with this IP address by using the following command:
set mls include
To configure the router, follow the steps below:
Enable MLS IP in global configuration:
Router(config)#mls rp ip
Assign a VTP domain on one MLS interface. The show vtp domain command on the switch provides the VTP domain name; our example is "sales":
Router(config-if)#mls rp vtp-domain sales

多层交换学习资料

推荐阅读

q7和x5怎么选？

维C不是越多越好！提醒：泡腾片别天天喝

摔跤是什么意思

无锡孕妇可以接种流感疫苗吗

店铺TB客是什么意思

瓷砖美缝打蜡的方法和注意事项

我的抖音封号了怎么办

弘阔的寓意

廉政标语

鹿茸怎么吃鹿茸的吃法

增加进气量能使汽车节油吗

女生最好就业的专业，女生就业前景好的专业

雪纳瑞的性格优缺点？活泼开朗但爱打架

美国服务器要如何租用？

漯河高铁票查询系统，通辽到漯河火车票查询

轻轨是什么